Autre Questions

What is the difference between the main stream and the sub stream?

Mainstream: is the primary video feed. Mainstream provides the highest video quality, and is the stream the DVR / NVR uses when saving footage to the internal hard disk drive (HDD). Mainstream settings can be adjusted to increase or decrease recording resolution. These settings will impact recording file size and available recording time. Hard Disk Drive (HDD)

Sub-stream: is the secondary video feed. Sub-stream provides a lower quality video stream, and is typically used to stream video to computers, smartphones, or tablets over the Internet. This allows you to reduce streaming quality for live or remote viewing, while maintaining higher quality on the mainstream for HDD recording and storage.

 

When is each one used?


Mainstream: is the primary video feed  mainly use for recording..
Sub-stream: is used mainly for remote viewing from computers, smartphones, or tablets over the Internet from outside the network..

 

How does bit rate relate to the Resolution and Frame rate?

The combination of frame rate and resolution based on the type of compression will need bandwidth necessary to accomplish. The higher the resolution/frame rate combination the more bandwidth or bit rate is necessary. The link below is to a bit rate chart that discusses in greater detail.

H.264+ Bit Rate Chart

 

Will the exported password reset XML file expire?

The password reset File exported via SADP, IVMS4200 and Batch configuration tool import/code procedure for password reset needs to be done within 3 days or it will expire.

Be sure not to power down or reboot the camera within this time frame.

Does Hikvision require any additional licensing fee?

No licensing fees required for non-Hik Central products.

Does Hikvision require any additional licensing fee?

No licensing fees required.

How can I request an RMA for my Hikvision products

Click here for more detailed information on Hikvision USA RMA policy.

IMPORTANT! Ce modèle nécessite un logiciel non standard. N'installez pas de logiciel standard (par exemple, v.4.1.xx) sur ce modèle. Cela endommagerait définitivement votre système. Vous devez utiliser le logiciel personnalisé v.4.1.25 à partir de la page du produit iDS-9632NXI-I8/16S

View the most updated version of this document here:

https://techsupportca.freshdesk.com/en/support/solutions/articles/17000113531-i-series-nvr-firmware-upgrade-instructions

 

The I-series NVR (such as the DS-7716NI-I4) is one of Hikvision's most popular and feature-rich recorders. As such, many firmware revisions have been introduced over the years to continually ensure the product is compatible with the newest technology available. Due to the many revisions, we recommend that the user closely follows the instructions below in order to reduce the amount of time spent as well as the chance of failure.

 

Database Optimization and Repair

As more affordable IP cameras are introduced over time with greater video resolution and data sizes, more efficient database management also becomes necessary. The introduction of firmware v4.0 brought about a new database architecture in order to be futureproof.

 

After upgrading to v4.X, the recorder database will need to be converted and optimized. If you are experiencing issues where playback is expected but not found, make sure "Database Repair" is performed as indicated in the procedures and scenarios below.

 

Preparing the Upgrade

Before proceeding with upgrade, it is recommended that NVR configuration file is exported from the NVR over the network or on to a local USB drive.

 

Upgrading from v3.4.92 build 170518 or Older

  1. All recorders must reach v3.4.92 before proceeding further. Upgrading from versions before v3.4.92 directly to any version of v4.X will likely cause the recorder to fail.
  2. If the recorder is already at v3.4.92, a full factory default is highly recommended before upgrading to any version of v4.X. There is a high chance of unit failure (requiring RMA) if the unit is not defaulted before upgrade.
  3. After reaching v3.4.92 and performing a full factory default, an upgrade directly to v4.50.00 is acceptable.
  4. After the upgrade is completed and the recorder is reprogrammed, it may be beneficial to perform a Database Repair. For details, refer to the section "Database Optimization and Repair" above.
  5. To verify repair progress, you may refer to the HDD status, or search the recorder log for repair started and stopped entries. Note that while the HDD is repairing, new recordings are still being made, but some existing recordings may not be searchable until repair is complete.
  6. If you continue to observe playback issues after database repair, ensure there are no power, network, or motion detection issues. Should the problem persist, contact technical support.

 

Upgrading from Any v4.X Build to v4.50.00.

  1. Any v4.X build can be upgraded directly to v4.50.00.
  2. Export configuration is highly recommended before performing the upgrade.
  3. If upgrading from any v4.X version that was not v4.22.005, a Database Repair is recommended. Refer to Step 4 and onwards in the previous section.

 

Downgrading

Downgrading is not recommended. Due to new features and parameters constantly being added, downgrading may cause the NVR to factory default itself or require a manual default to operate properly.

En téléchargeant et en utilisant des logiciels et autres matériels disponibles sur ce site, vous acceptez d'être lié par les Conditions Générales d'Utilisation de HIKVISION. Si vous n'acceptez pas ces conditions, vous ne pouvez télécharger aucun de ces documents. Si vous êtes d'accord sur votre entreprise, vous déclarez et garantissez que vous avez le pouvoir de lier votre entreprise aux Conditions Générales d'Utilisation . Vous déclarez et garantissez également que vous avez l'âge légal de la majorité dans la juridiction dans laquelle vous résidez (au moins 18 ans dans de nombreux pays).